24/7 Furnace Repair Referral Line • Mount Prospect, IL (60056) Call (847) 722-8000
Furnace Repair Pros Furnace Repair Pros Call (847) 722-8000

Gas Furnace Igniter vs. Flame Sensor Failure: How to Tell

Two of the smallest, least expensive parts inside your gas furnace—the hot-surface igniter and the flame sensor—are responsible for a massive share of winter no-heat calls across Mount Prospect. Because both parts cause the furnace to fail early in the heating cycle, homeowners often confuse them. Knowing the difference helps you describe symptoms accurately when you call our Mount Prospect furnace repair line at (847) 722-8000.

Direct Answer: A bad hot-surface igniter prevents the burners from lighting at all (no flame, no orange glow). A dirty or failing flame sensor allows the burners to ignite normally, but shuts the gas valve off 3 to 5 seconds later because the control board cannot verify the flame.

Igniter vs. Flame Sensor: Side-by-Side Comparison

FeatureHot-Surface IgniterFlame Sensor Rod
Role in Heating CycleHeats up to ignite gas at burnerProves flame is present via microamp signal
What You Hear & SeeInducer runs, click, NO flame ever lightsBurners ignite brightly, then shut off in 3–5 sec
MaterialSilicon carbide (brittle) or silicon nitrideStainless/kanthal metal rod in ceramic base
Typical Lifespan3 to 8 heating seasonsOften lasts 10+ years with periodic cleaning
Related ServiceIgniter & Pilot RepairCold Air Troubleshooting

How a Hot-Surface Igniter Fails

Every time your thermostat calls for heat during a cold week in Hatlen Heights or Randhurst Village, the control board sends 120V or 24V power to the igniter element. Within 15 to 25 seconds, it glows bright orange—hot enough to ignite natural gas cleanly as the gas valve opens. Over thousands of thermal expansion cycles, older silicon-carbide igniters develop microscopic fractures or white oxidation spots. Eventually the circuit opens completely.

When an igniter fails, you will hear the draft inducer motor spin up and a relay click on the control board, followed by silence where the whoosh of burner ignition should be. After three or four failed attempts, the furnace locks out and blinks a fault code. Because silicon-carbide elements are as fragile as pencil lead, even minor cabinet vibration from an aging blower motor can crack a weakened igniter.

How a Flame Sensor Fails

The flame sensor sits on the opposite side of the burner assembly from the igniter. Once gas ignites, the flame bathes the metal sensor rod, rectifying a tiny AC voltage into a DC microamp signal (typically 1.5 to 5+ microamps) that travels back to the control board. If household dust, pet hair, or combustion silica (often from laundry detergent fumes or basement dust) bakes onto the rod, electrical resistance rises and the microamp signal drops below the board's safety threshold.

To prevent unburned gas from filling your basement in Scarsdale Estates or Prospect Meadows, the control board immediately closes the gas valve within three to five seconds of ignition. This looks and sounds like a healthy startup that abruptly dies—and it is a classic cause of furnace short cycling.

Why Both Parts Matter for Older vs. Newer Furnaces

In older Mount Prospect homes built in the 1950s and 1960s that still run legacy standing-pilot furnaces, a thermocouple performs a similar safety job to a flame sensor: if the pilot flame goes out, the thermocouple cools and closes the main gas valve. Whether you have a standing pilot or a modern 96% condensing gas furnace, never bypass a flame sensor or safety switch.

If your furnace is located near a basement laundry room—a very common layout in mid-century homes around Downtown Mount Prospect—airborne dryer lint and fabric softener vapors accelerate buildup on the flame sensor rod. Keeping the laundry area clean and changing your furnace filter regularly reduces sensor fouling significantly.

What a Technician Checks On-Site

  1. Ohms Resistance Test: Checking igniter cold resistance with a multimeter (typically 40–90 ohms for healthy silicon-carbide elements; an open circuit reads OL).
  2. Voltage Supply Verification: Confirming the control board is actually sending 120V or 24V to the igniter plug during the warm-up window.
  3. Microamp Flame Signal Test: Measuring live DC microamps in series with the flame sensor wire while burners fire to confirm signal strength above manufacturer minimums.
  4. Ground Continuity Check: Ensuring the burner box and control board share a clean electrical ground, since poor grounding mimics a bad flame sensor.
  5. Upgraded Replacement: Installing a durable silicon-nitride igniter kit when replacing fragile carbide elements.

If your furnace is clicking without lighting or shutting off three seconds after ignition, schedule furnace igniter and flame sensor repair or 24/7 emergency dispatch by calling (847) 722-8000 today.

Frequently Asked Questions

Need a Local Furnace Technician in Mount Prospect?

Call our 24/7 dispatch line to connect directly with an independent local heating technician.

Call (847) 722-8000
Call (847) 722-8000 — 24/7 Furnace Dispatch